The Role of Nondestructive Testing in the Assessment and Quality Control of Asphalt Pavement Compaction and Construction Uniformity

Document Type : Original Article

Authors
1 Civil Engineering Department, K. N. Toosi University of Technology, Tehran, Iran.
2 Assistant Professor, School of Civil Engineering, Iran University of Science and Technology (IUST), Tehran, Iran.
Abstract
Advances in nondestructive testing and intelligent construction technologies have enabled faster and more spatially extensive assessment of asphalt pavement quality. However, measurement capability does not necessarily indicate a technology’s readiness for quality assurance and acceptance. This analytical review examines selected technologies from process control to acceptance, focusing on density, compaction uniformity, and thermal conditions affecting asphalt placement and compaction. Scientific literature, technical reports, standards, technical specifications, and contractual documents were reviewed. Three technologies were evaluated in terms of measured response, relationship to an acceptance quality characteristic, validation, reliability, and acceptance readiness: the dielectric profiling system (DPS) based on ground penetrating radar (GPR), intelligent compaction, and thermal profiling systems mounted on pavers. The findings indicate that DPS offers a more direct pathway toward density-related acceptance because its calibrated output can be expressed as density or air void content. Nevertheless, its application requires calibration and validation tailored to project conditions. Intelligent compaction is more applicable to controlling roller coverage and compaction uniformity, whereas thermal profiling is better suited to monitoring thermal uniformity and identifying areas susceptible to thermal segregation. Iranian specifications establish a lot and sublot structure and a mechanism for calculating pay factors, but no validated procedure exists for incorporating continuous data from these technologies into acceptance decisions. Accordingly, a framework comprising six stages is proposed: defining the quality characteristic and decision objective, validating the measurement, conducting pilot and shadow implementation, establishing verification procedures, incorporating data into acceptance decisions, and developing contractual provisions for phased implementation.
Keywords

­ Abufares, L., Chen, Y. and Al-Qadi, I. L. (2025a). Asphalt concrete density monitoring during compaction using roller-mounted GPR. Automation in Construction, Vol. 174, Article 106158.
 doi.org/10.1016/j.autcon.2025.106158
­ Abufares, L., Chen, Y. and Al-Qadi, I. L. (2025b) .Isolating surface moisture in
ground-penetrating radar signals for accurate asphalt concrete density prediction. Transportation Research Record, Vol. 2679,
No. 8, 493–508.
doi.org/10.1177/03611981251334631
­ Ayar, P., Ashnavar, A. and Ruhi, A. (2023)­.
A review on using ultrasonic waves to evaluate the characteristics of asphalt pavement. Journal of Nondestructive Testing Technology, Vol. 3, No. 2, 62–70.
doi.org/10.30494/JNDT.2023.400881.1120
­ Baghchesaraei, O. R., Ayar, P., Khademi, A., Taherkhani, B., & Hosseini Lavassani, S. (2026). Core Concepts for a Circular Future: Modularity, Repairability, and Recyclability. In Designing for a Circular Future. Springer Nature.
­ Cao, Q. and Al-Qadi, I. L. (2021). Signal stability and the height-correction method for ground-penetrating radar in situ asphalt concrete density prediction .Transportation Research Record, Vol. 2675, No. 9, 835–847. doi.org/10.1177/03611981211004585
­ Chang, G. K., Mohanraj, K., Stone, W. A., Oesch, D. J. and Gallivan, V. L. (2018). Leveraging intelligent compaction and thermal profiling technologies to improve asphalt pavement construction quality: A case study. Transportation Research Record, Vol. 2672, No. 26, 48–56.
doi.org/10.1177/0361198118758285
­ Chen, Y., Abufares, L. and Al-Qadi, I. L. (2026). Reliability of in-situ asphalt concrete density prediction by roller-mounted GPR. NDT & E International, Vol. 161, Article 103708.
doi.org/10.1016/j.ndteint.2026.103708
­ Dehbandi, R., Shirpourasl, Z. and Asnaashari, E. (2026). Digital transformation of construction quality management: Systematic review of adoption and governance. Automation in Construction, Vol. 191, Article 107166. doi.org/10.1016/j.autcon.2026.107166
 
­ Diamanti, N., Annan, A. P., Jackson, S. R. and Klazinga, D. (2021). A GPR-based pavement density profiler: Operating principles and applications”, Remote Sensing, Vol. 13, No. 13, Article 2613.
doi.org/10.3390/rs13132613
­ Federal Highway Administration. (2021). Spotlight on pavement density: Minnesota Department of Transportation working with dielectric profiling systems. Publication No. FHWA-HIF-21-040, Washington, DC: U.S. Department of Transportation.
­ Federal Highway Administration. (2024). NDT and ICT for asphalt pavement construction: Tech brief. Publication
No. FHWA-HIF-24-031, Washington, DC: U.S. Department of Transportation.
­ Federal Highway Administration. (2026). Quality assurance procedures for construction. 23 CFR Part 637, Subpart B, current as of August 20, Washington, DC: U.S. Department of Transportation.
­ Hoegh, K., Steiner, T., Teshale, E. Z. and Dai, S. (2020). Minnesota Department of Transportation case studies for coreless asphalt pavement compaction assessment Transportation Research Record, Vol. 2674,
No. 2, 291–301.
doi.org/10.1177/0361198120907582
­ Jeong, J., Wang, Y. D., Ghanbari, A., Nash, C., Nener-Plante, D., Underwood, B. S. and Kim, Y. R. (2020). Pavement performance predictions using performance-volumetric relationship and evaluation of construction variability: Example of MaineDOT shadow project for the development of performance-related specifications Construction and Building Materials, Vol. 263, Article 120150. doi.org/10.1016/j.conbuildmat.2020.120150
­ Kaseer, F., Muslim, H. B., Haider, S. W. and Akerly, E. (2025). Use of dielectric profiling system for rapid continuous measurement of asphalt mix density: Case studies in Michigan. Transportation Research Record, Vol. 2679,
No. 7, 773–790.
doi.org/10.1177/03611981251328973
­ Kaseer, F., Roberts, R., Akerly, E. and Cist, D. (2026). Development and validation of a new dielectric profiling system dielectric–density calibration model using laboratory and field data. Transportation Research Record, 1–19. doi.org/10.1177/03611981261429869
­ Khazanovich, L., Hoegh, K., Conway, R. and Dai, S. (2017). Nondestructive evaluation of bituminous compaction uniformity using rolling density. SHRP2 Report R06C, Technologies to Enhance Quality Control on Asphalt Pavements, Washington, DC: Second Strategic Highway Research Program.
­ Muslim, H. B., Haider, S. W. and Khazanovich, L. (2024). Flexible pavement longitudinal joint quality evaluation using non-destructive testing. Journal of Road Engineering, Vol. 4, No. 2, 189–202. doi.org/10.1016/j.jreng.2024.03.001
­ National Academies of Sciences, Engineering, and Medicine. (2023a). Incorporating nondestructive testing in quality assurance of highway pavement construction: Conduct of research report. NCHRP Web-Only Document 375, Washington, DC: The National Academies Press.
 doi.org/10.17226/27442
­ National Academies of Sciences, Engineering, and Medicine. (2023b). Incorporating nondestructive testing in quality assurance of highway pavement construction: Manual. NCHRP Research Report 1082, Washington, DC: The National Academies Press. doi.org/10.17226/27443
­ Nevalainen, N. and Pellinen, T. (2016).
The use of a thermal camera for quality assurance of asphalt pavement construction. International Journal of Pavement Engineering, Vol. 17, No. 7, 626–636. doi.org/10.1080/10298436.2015.1007240
­ Plan and Budget Organization of Iran. (2011). Regulations for asphalt pavements of Iran. Publication No. 234, 1st revision, Tehran: Office of the Technical and Executive System.
­ Plan and Budget Organization of Iran. (2019). Instruction for evaluation of quality and technical specifications of executed works. Publication No. 773, Tehran: Office of the Technical and Executive System. (in Persian)
­ Plan and Budget Organization of Iran. (2026). General technical specifications for roads. Publication No. 800-101, 3rd revision, Tehran: Office of the Technical and Executive System.
­ Saleh, N. F., DeCarlo, K., Underwood, B. S., Pine, W. J., Huber, G., Tran, N., West, R. C. and Kim, Y. R. (2023). Case studies of asphalt pavement quality assurance specifications, performance-related specifications, and performance-based specifications. Transportation Research Record, Vol. 2677, No. 11, 682–696.
doi.org/10.1177/03611981231166685
­ Savan, C. M., Ng, K. W. and Ksaibati, K. (2016). Benefit-cost analysis and application of intelligent compaction for transportation. Transportation Geotechnics, Vol. 9, 57–68. doi.org/10.1016/j.trgeo.2016.07.001
­ Sivagnanasuntharam, S., Sounthararajah, A., Ghorbani, J., Bodin, D. and Kodikara, J. (2023). A state-of-the-art review of compaction control test methods and intelligent compaction technology for asphalt pavements. Road Materials and Pavement Design, Vol. 24, No. 1, 1–30. doi.org/10.1080/14680629.2021.2015423
­ Steiner, T., Hoegh, K., Teshale, E. Z. and Dai, S. (2020). Method for assessment of modeling quality for asphalt dielectric constant to density calibration. Journal of Transportation Engineering, Part B: Pavements, Vol. 146, No. 3, Article 04020054.
doi.org/10.1061/JPEODX.0000210
­ Sui, X., Wang, S., Leng, Z. and Gong, M. (2025). In-situ density measurement using GPR considering random pore distribution of asphalt pavement, Measurement, Vol. 243, Article 116479. doi.org/10.1016/j.measurement.2024.116479
­ Von Quintus, H. L., Nabizadeh, H., Hand, A. and Hajj, E. (2023). A practice for including intelligent construction equipment in quality assurance programs. Publication
No. FHWA-HIF-23-007, Washington, DC: Federal Highway Administration.
­ Wang, S. and Al-Qadi, I. L. (2022). Impact and removal of ground-penetrating radar vibration on continuous asphalt concrete pavement density prediction. IEEE Transactions on Geoscience and Remote Sensing, Vol. 60, Article 5106414.
doi.org/10.1109/TGRS.2021.3106041
­ Wang, Y. D., Liu, J. and Liu, J. (2023). Integrating quality assurance in balance mix designs for durable asphalt mixtures: State-of-the-art literature review. Journal of Transportation Engineering, Part B: Pavements, Vol. 149, No. 1, Article 03122004. doi.org/10.1061/JPEODX.PVENG-957
­ Wang, S., Al-Qadi, I. L. and Cao, Q. (2020). Factors impacting monitoring asphalt pavement density by ground penetrating radar .NDT & E International, Vol. 115, Article 102296. doi.org/10.1016/j.ndteint.2020.102296
­ Wang, S., Sui, X., Leng, Z., Jiang, J. and Lu, G. (2022a). Asphalt pavement density measurement using non-destructive testing methods: Current practices, challenges, and future vision. Construction and Building Materials, Vol. 344, Article 128154. doi.org/10.1016/j.conbuildmat.2022.128154
­ Wang, S., Leng, Z., Zhang, Z. and Sui, X. (2022b). Automatic asphalt layer interface detection and thickness determination from ground-penetrating radar data. Construction and Building Materials, Vol. 357, Article 129434. doi.org/10.1016/j.conbuildmat.2022.129434
­ Wang, Y., Li, J., Zhang, X., Yao, Y., & Peng, Y. (2024). Recent development in intelligent compaction for asphalt pavement construction: Leveraging smart sensors and machine learning. Sensors, 24(9), Article 2777. doi.org/10.3390/s24092777
­ Wang, S., Yang, M., Zhang, Y., Huang, X., Ma, T. and Wang, D. (2026) .A comprehensive evaluation of non-destructive density and moisture content measurement of asphalt pavement during construction using ground-penetrating radar. Journal of Road Engineering, Vol. 6, 51–73.
doi.org/10.1016/j.jreng.2025.12.001
­ Xu, Q. and Chang, G. K. (2016). Adaptive quality control and acceptance of pavement material density for intelligent road construction. Automation in Construction,
Vol. 62, 78–88.
doi.org/10.1016/j.autcon.2015.11.004
­ Yao, Y. and Song, E. (2023). Intelligent compaction methods and quality control. Smart Construction and Sustainable Cities, Vol. 1, No. 1, Article 2.
 doi.org/10.1007/s44268-023-00004-4
­ Yoon, S., Hastak, M. and Lee, J. (2018). Suitability of intelligent compaction for asphalt pavement quality control and quality assurance. Journal of Construction Engineering and Management, Vol. 144, No. 4, Article 04018006.
 doi.org/10.1061/(ASCE)CO.1943-7862.0001401
­ Zaumanis, M., Poulikakos, L. D. and Partl, M. N. (2018). Performance-based design of asphalt mixtures and review of key parameters. Materials & Design, Vol. 141, 185–201. doi.org/10.1016/j.matdes.2017.12.035
­ Zhan, Y., Zhang, Y., Nie, Z., Luo, Z., Qiu, S., Wang, J., Zhang, A. A., Ai, C., Tang, X. and Tan, C. (2023). Intelligent paving and compaction technologies for asphalt pavement .Automation in Construction, Vol. 156, Article 105081. doi.org/10.1016/j.autcon.2023.105081
­ Zhou, F., Hu, S. and Newcomb, D. (2020). “Development of a performance-related framework for production quality control with ideal cracking and rutting tests. Construction and Building Materials, Vol. 261, Article 120549. doi.org/10.1016/j.conbuildmat.2020.120549